Industrial Epoxy Flooringin Aurora, Longmont, Erie, Parker and across the Front Range
Forklifts, pallet jacks, dropped tools and spilled everything. An industrial floor is specified for the worst day, not the average one.
Industrial floors fail in ways residential floors never see. It is not hot tires and road salt, it is point loading from a loaded pallet jack, steel wheels on a slab, solvents and hydraulic fluid sitting where they landed, and joints that have been chipping out for a decade under traffic. The system has to be chosen for that, and the slab has to be genuinely repaired first.
Joints and edges are where industrial floors go
On a warehouse or shop floor the coating rarely fails in the middle of a bay. It fails at the control joints and the edges, because that is where a hard wheel hits an unsupported edge thousands of times and chips it away.
That means joint treatment is not a detail on an industrial job, it is the job. Joints get cleaned out, repaired and filled so the edges are supported and a wheel rolls across rather than into them. Do that properly and the floor holds. Skip it and the failure starts within months, from the joints outward.
Chemical exposure and cleanability
Bare concrete is porous, which means every oil drip, coolant spill and solvent splash soaks in and stays. Over time that is both a stain and a problem — contaminated concrete is harder to bond to later, so an uncoated shop floor gets progressively more expensive to fix the longer it is left.
A sealed floor keeps spills on the surface where they can be cleaned up, and a properly bonded epoxy resists the oils, brake fluid and antifreeze that a mechanical space generates daily.
What you get
- Control joints cleaned, repaired and filled so edges are supported
- Oil-contaminated slabs remediated before any coating is applied
- Heavier specification for forklift, pallet jack and steel-wheel traffic
- Resists oil, hydraulic fluid, brake fluid, coolant and antifreeze
- Grind and seal available for large areas where dust control is the priority
Open 24 hours — call or text anytime
Our expertise
How we approach industrial epoxy flooring
The prep on an industrial slab is heavier than anywhere else. Years of oil contamination has to be dealt with before a coating will bond at all. Spalled areas under traffic lanes, chipped joints, old patches and previous failed coatings all get ground back and rebuilt before anything new goes on.
The systems are the same family we use everywhere — a ground-and-bonded epoxy base with a polyaspartic topcoat — specified heavier for the traffic, with the joint work that the environment demands. Grind and seal is also a genuine option on a large shop floor where the priority is dust control and cleanability rather than a decorative finish, and it is the most cost-effective way to cover a lot of square footage.
Industrial jobs vary enormously and the honest answer on specification comes from walking the floor: what runs on it, what gets spilled on it, how much downtime you can take, and what condition the joints are actually in. Call or text Brock and we will come and look.
Industrial Epoxy Flooring questions
Can you coat a shop floor that is soaked in oil?+
Usually, but the contamination has to come out first — a coating will not bond through oil. That remediation is part of the quote and it is the step that decides whether the floor lasts. The longer a slab is left uncoated, the deeper it goes.
Will it handle forklift traffic?+
The specification is built for the traffic on your floor, and the joints get the attention they need, because that is where hard-wheel traffic actually breaks a coating. Tell us what runs on it and we will spec for that.
Is a full coating always the right answer for a warehouse?+
No. If the priority is dust control and easy cleaning over a large area rather than a decorative finish, grind and seal covers far more square footage for the money. We will tell you which one your building actually needs.
Industrial Epoxy Flooring in Aurora, Longmont, Erie, Parker and beyond
Based in Northern Colorado and working throughout the region.
Other services we offer
Epoxy Flooring
A hard, chemical-resistant epoxy floor is only as good as the concrete it is bonded to. We grind first, repair first, and coat last.
Learn more →
Polyaspartic Flooring
UV stable, fast curing, and it will still cure when the garage is cold. This is the topcoat that does the surviving.
Learn more →
Garage Floor Coating
The most abused slab you own, coated properly. Hot tires, road salt, snowmelt and freeze-thaw — planned for, not hoped past.
Learn more →
Patio Coating
Outdoor concrete at altitude gets punished. A patio coating has to survive UV, freeze-thaw and being walked on wet.
Learn more →
Residential Epoxy Flooring
Garages, basements, laundry rooms and workshops — coated in a house that people are still living in, and left clean.
Learn more →
Commercial Epoxy Flooring
A commercial floor has two jobs: survive the traffic, and not cost you trading days while it goes in.
Learn more →Get a price on your floor
Free estimates across Northern Colorado. Call or text Brock directly.